-
GENERAL SPECIFICATIONS
High-fidelity Bluetooth® with aptX® transmission and extended range
Supports all Bluetooth-enabled devices
Hand-built wood cabinet with magnetic speaker grills
Auxiliary analog mini-jack input
Built-in auto voltage switching power supply
Type
Powered Bluetooth speaker
Amplifier type
Dual class AB monolithic
Power output
60W peak total (15W RMS, 30W peak per channel), AES
Drivers
2.75” aramid fiber woofers
3/4“ Silk dome tweeters
Inputs
Bluetooth, 3.5mm stereo mini-jack analog
Analog input impedance
10K ohms unbalanced
Frequency response
65Hz-22kHz (±2.0dB)
SNR
95db (typical A-weighted)
THD+N
<0.05% at all power settings
Crosstalk
-50dB
Power filtering
3-stage redundant regulation
Input voltages
100-240V, 50/60Hz auto-switching
Protection
Output current limiting, thermal over-temperature, power on/off transient protection
-
BLUETOOTH SPECIFICATIONS
Bluetooth receiver type
Bluetooth 5.0 audio
Supported Bluetooth codecs
aptX, AAC, SBC
Supported Bluetooth profiles
A2DP, AVRCP
Wireless operation range
up to 100ft (30m) typical
D/A converter
TI PCM5102A
Input bit depth
24-bit (upsampled)
Input data rate
Determined by Bluetooth
Wireless latency
~30 milliseconds (ms)
-
WEIGHTS AND MEASURES
Product dimensions
4.25”(H) x 12.25”(W) x 5.50”(D)
Shipping weight
10lbs (4.6kg)
Shipping box dims
10.5” (H) x 16” (W) x 7.5” (D)
-
ENVIRONMENTAL REQUIREMENTS
Operating temperature: 24° to 105°F (0°C to 40°C)
Storage temperature: -4° to 115°F (-20°C to 46°C)
Relative humidity: 5% to 95% non-condensing
-
MATERIALS AND CONSTRUCTION
18mm thick MDF cabinets with real wood veneer
3/4 silk dome tweeters with neodymium magnets
2.75″ aramid fiber woofers with advanced voice coils
-
INCLUDED ACCESSORIES
Power cable
Antenna
Mini-jack audio cable, 1.5 meters (~5 feet)
Microfiber speaker bag
Quickstart guide
-
DIGITAL TO ANALOG CONVERTER CHARACTERISTICS
The B2 Bluetooth speaker system utilizes the TI PCM5102A DAC, widely known for it’s low noise and high fidelity. Due to the PCM5102A’s high signal-to-noise specs, the fact that digital signal is converted (upsampled) to 24-bits and the added benefit of triple redundancy power source conversion and filtering, the B2 presents impressive low noise and low distortion characteristics with a noticeable improvement over other Bluetooth speakers.
-
EXTENDED WIRELESS RANGE
Most Bluetooth speakers have very limited range, usually within just one room. But with careful signal management circuitry and antenna tuning, we offer a superior solution that will reach more than one room with no degradation in audio quality.
-
HIGH QUALITY BLUETOOTH AUDIO
The B2 features aptX coding which is an advanced Bluetooth audio codec that provides much higher-quality sound than previous versions. The B2 is backwards-compatible with all previous Bluetooth implementations so you can wirelessly stream music from any device and still enjoy outstanding sound.
-
CUSTOM BUILT AUDIO COMPONENTS
Audioengine designs and manufactures our own tweeters, woofers, and many other critical components. In other words, these are not “box built” speakers with off-the-shelf parts but entirely designed to our specifications. What we do not fabricate directly in our factories we have custom-made to our specifications (parts such as toroidal transformers, magnets, and wiring harnesses, for example). The speaker cabinets, drivers, bass port designs, amplifiers, and crossovers are all painstakingly tuned together for each Audioengine model. This, in turn, makes for a much more efficient system that requires much less power than traditional AV stereo receivers and passive speakers.
-
BASED ON STUDIO MONITOR DESIGNS
Studio monitor speakers are used by producers and engineers in recording and production studios. They are designed with a theoretical flat frequency response which allows the engineer to create a final mix in such a way that the recorded music will sound good on most other speakers. Although Audioengine speakers are not designed to be up-close “nearfield” studio monitors, we do carry over much of the same higher-end technology, components, and design philosophy for all Audioengine speaker systems.
-
DRIVERS
Audioengine uses audiophile-quality, ferrofluid-cooled, silk dome tweeters with neodymium magnets. Silk tweeters hold up well under high power and the edge-driven design gives very smooth response. The custom woofers are aramid fiber woven glass composite with rubber surrounds. Aramid fiber is obviously very strong, which means that the woofer retains its shape when being driven at high levels. The speaker materials and construction are very robust, therefore speaker grills aren’t needed. In other words, we did our homework on the speaker drivers and they will sound and look great after many years of use.
-
CABINET
To minimize unwanted resonances and distortion, Audioengine cabinets have thick high-resin MDF walls with extensive internal bracing. Heavy internal sound-damping material is also used to reduce unwanted sound reflections inside the cabinet. The B2 cabinet is a unique design in that it has dual sub-enclosures to prevent cross-interference, while each side contains its own tuned, front-port bass slot.
-
POWER AMPLIFIER
The class A/B amplifiers in Audioengine speaker systems are very conservatively-rated analog designs. Each subsystem is tuned together for all models, providing a much more efficient system requiring less power than passive speakers and separate amplifiers. An auto-standby idle mode is also included to conserve power when you’re not playing music.
-
SHIELDING
Both drivers are magnetically-shielded which allows protection for CRT displays and hard-drive music players.
